Avaya J100 Series Installing And Administering Download Page 80

Page: 80 / 528

4. Select

IP Configuration

Ethernet IPv4

The phone displays the parameters for IP configuration.

IP configuration field description

Configuration Parameter Name

Description

The following parameters are available in Ethernet IPv4 menu:

Use DHCP

Specifies the access to view or manually enter the
IP address.

Select one of the following:

•

YES

: Selects the DHCP option to view the IP

addresses.

•

: Selects the DHCP option to enter the IP

addresss.

Phone

Specifies the IP address of the phone. The
available format is

nnn.nnn.nnn.nnn.

Gateway

Specifies the gateway of the phone. The available
format is

nnn.nnn.nnn.nnn.

Mask

Specifies the network mask. The available format is

nnn.nnn.nnn.nnn.

The following parameters are available in VLAN menu:

802.1Q

Choose one of the following options:

•

Auto

: Automatic mode.

•

: Turns on the configuration.

•

Off

: Turns off the configuration.

VLAN ID

Specifies the ID for VLAN. The available format is

dddd

VLAN Test

Specifies the time in seconds, the phone waits for
the DHCP server response. The available format is

ddd

The following parameters are available in the Servers menu:

HTTP server

Specifies the IP address of the HTTP file server.
The available format is

nnn.nnn.nnn.nnn.

HTTPS server

Specifies the IP address of the HTTPS file server.
The available format is

nnn.nnn.nnn.nnn.

DNS server

Specifies the IP address of the DNS server. The
available format is

nnn.nnn.nnn.nnn.

SNTP server

Specifies the time server settings.

STUN server

Specifies the STUN server settings.

Table continues…

Phone configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 80 / 528

Search results

Summary of Contents for J100 Series

Reviews: