manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 518 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 518

Appendix C: Network progress tones

overview

The SIP-based Avaya J100 Series IP Phones provide country-specific network progress tones
which are presented to the user at appropriate times. The tones are controlled by administering the
COUNTRY parameter for the country in which the deskphone will operate. Each Network Progress
Tone has the following six components:

• Dialtone

• Ringback

• Busy

• Congestion

• Intercept

• Public Dialtone

All countries listed in this appendix are applicable to the 96xx phones. Some of the dialtone entries
have changed from previous releases to be distinctively different than the public dialtone entries.

Alphabetical country list

A:

• Abu Dhabi
• Albania
• Argentina
• Australia
• Austria

B:

• Bahrain
• Bangladesh
• Belgium
• Bolivia
• Bosnia

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

518

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments