Home
/
Avaya
/
J100 Series
/
Installing And Administering

Avaya J100 Series, Installing And Administering, Page: 256 / 528

Share

Page: 256 / 528

Avaya J100 Series Installing And Administering Download Page 256

Parameter name

Default value

Description

WMLPROXY

Null

Specifies the address of an HTTP
proxy server that will be used by
the WML browser.

The allowed values must be in
the dotted-decimal (IPv4) or DNS
name format, separated by
commas without any intervening
spaces. The value can contain up
to 255 characters.

WMLEXCEPT

Null

Specifies the IP addresses or
domains for which the HTTP
proxy server set as the
WMLPROXY value will not be
used.

Allowed values can contain up to
255 characters and must be
separated by commas without
any intervening spaces.

Voicemail

The Voicemail feature is used to dial the configured voice mail number to receive a voice
message.

Configuring Voicemail by using the web interface

About this task

To configure the Voicemail list using the web interface, do the following steps:

Procedure

1. Log in to the web interface as an administrator.

2. In the navigation pane, click

SIP

.

3. In the Miscellaneous area, specify the number to access the voice mail in a non-Avaya

environment.

4. Click one of the following:

•

Save

•

Reset to Default

•

Help

Voicemail configuration

Use the

46xxsettings.txt

file to set the following parameters:

Feature and application configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

256

Comments on this document? [email protected]

«
...
254
255
256
257
258
...
»

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments