Avaya J100 Series Installing And Administering Download Page 13

Page: 13 / 528

Change history

Issue

Date

Summary of changes

Release 3.0

June 2018

• Added Avaya J139 IP Phone specification and features

• Extended Device Enrollment Services description

• Added “Broadsoft Device Management” section

• Added “Feature administration” chapter

• Updated Appendix

• Minor phrasing and spelling improvements throughout the

document

Release 4.0

December 2018

• Extended “Feature administration” chapter

• Extended IPv4 configuration description

• Restructured “Initial setup and connectivity” chapter

• Added “Phone installation” chapter

• Updated Appendix

• Minor phrasing and spelling improvements throughout the

document

Release 4.0.1

April 2019

• Extended “Feature and application configuration” chapter

• Updated Appendix

Release 4.0.2

July 2019

• Extended “Feature and application configuration” chapter

• Updated “Phone configuration” chapter

• Extended “Servers, VLAN, and IP configuration” chapter

• Updated Appendix

Release 4.0.3

October 2019

• Added Avaya J159 IP Phonespecification and features

• Extended “Feature and application configuration” chapter

• Updated “Phone configuration” chapter

• Updated Appendix

Release 4.0.4

January 2020

• Extended “Feature and application configuration” chapter

• Updated “Phone configuration” chapter

• Extended “Servers, VLAN, and IP configuration” chapter

• Updated Appendix

Table continues…

Change history

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 13 / 528

Search results

Summary of Contents for J100 Series

Reviews: