manualshive.com logo in svg

Avaya IP Office Phone Manager, Manual, Page: 308 / 324

Share
Download
Avaya IP Office Phone Manager Manual Download Page 308

Phone Based Administration

Page 308

- Issue 6a (Thursday, February 22, 2018)

IP Office Basic Edition

Comments on this document? [email protected]

17.8 System Reset

Use this feature to reset the system while retaining the currently programmed settings. Reset the system only when
advised to do so by technical support personnel. 

·

!

 WARNING 

This process will restart the phone system and disconnect all currently connected calls. 

·

The system reset begins immediately. It takes approximately 5 minutes.

·

This procedure is not listed when using the 

Next Procedure

 or 

Previous Procedure

 buttons to select a

procedure. 

1408/1416/9504/9508 Phone

1. At either of the first two extensions on the system, press 

Admin

. 

·

To do the above during a call, you may need to press the 

 

PHONE

 button to display the 

Admin

 soft key

option. If you access phone administration during a call, only the   

SPEAKER

,   

MUTE

 and 

 

HEADSET

buttons still affect the connected call. 

2. Use the 

 up or down 

 arrow buttons to scroll the display to 

System Administration

. When highlighted, press

Select

.

3. Dial 

#728

. 

4. At the 

Reset - Save All

 prompt press 

Proceed

. 

M7324/M7324N/M7310/M7310N/T7316/T7316E Phone

1. At either of the first two extensions on the system, press 

 

Feature **config

 (ie. 

Feature **266344

). 

·

If the system has a 

system password

 set, it is requested. Enter the password. 

2. The phone displays 

System Admin

. 

3. Dial 

#728

.

4. At the 

Reset - Save

 prompt press 

Enter

. 

·

To exit phone based administration at any time, press the 

Release

 button. To select a different process use the

Next Procedure

 or 

Previous Procedure

 buttons or dial another feature code.

ETR 18D/ETR 34D Phone

1. At either or the first two extensions on the system, press 

Feature 0 0

 followed by two presses of the first

intercom or call appearance button.

2.

System Administration:

 is shown on the display.

3. Dial 

#728

.

4. At the 

Reset - Save All

 prompt press 

Enter

. 

114

22

Summary of Contents for IP Office Phone Manager





































































































































































































































































































































Reviews:

No comments