manualshive.com logo in svg

Avaya H.323 9621G, Installing And Maintaining, Page: 14 / 94

Share
Download
Avaya H.323 9621G Installing And Maintaining Download Page 14

automatically starts reboot procedures that include a download if new software is available.

For more information, see 

About software distribution packages

 on page 65 and 

Downloading software packages

 on page 66.

Creating the pre-installation checklist

Before plugging in a 9608, 9611G, 9621G, or 9641G deskphone, verify all the following

requirements. Failure to do so prevents the deskphone from functioning properly and can

negatively impact the network. Print copies of this checklist for each server and deskphone.

Requirements for your network:

1.

The LAN uses Ethernet Category 5e cable to run the IPv4 or IPv6 version of
Internet Protocol.

2.

Your call server is updated with Avaya Aura

®

Communication Manager Release

6.0 or later. Avaya only supports 9608, 9611G, 9621G, and 9641G deskphones
running on Communication Manager 6.0 or later.

3.

Verify that the following circuit packs are installed on the switch:

• TN2602 or TN2302IP Media Processor circuit pack. Avaya recommends that

sites with a TN2302 IP Media Processor circuit pack must install a TN2602 circuit
pack to benefit from increased capacity.

• TN799C or D Control-LAN (C-LAN) circuit pack.

 Important:

Release 6.0 or later requires TN799C V3 or greater C-LAN circuit pack(s). For
more information, see the 

Communication Manager Software and Firmware

Compatibility Matrix

 on the Avaya support web site at 

http://www.avaya.com/

support

.

4.

Verify that the Avaya call server is configured correctly. For more information, see

Administering Avaya IP Deskphone H.323 9608, 9611G, 9621G, and 9641G

 and

Communication Manager documentation at: 

http://www.avaya.com/support

.

5.

Verify that the DHCP server and application are administered correctly. See

Administering Avaya IP Deskphone H.323 9608, 9611G, 9621G, and 9641G

.

6.

Verify that the HTTP/HTTPS server and application are administered correctly.
See 

Administering Avaya IP Deskphone H.323 9608, 9611G, 9621G, and

9641G

.

7.

Verify that the upgrade script and application files from the Avaya Support Web
site are loaded correctly on the HTTP/HTTPS server. See

http://www.avaya.com/

support

.

8.

If applicable, the DNS server is administered as described in the 

Administering

Avaya IP Deskphone H.323 9608, 9611G, 9621G, and 9641G

.

Installing the Deskphone

14     Installing and Maintaining Avaya IP Deskphone H.323 9608, 9611G, 9621G, and 9641G

August 2013

Comments? [email protected]

Summary of Contents for H.323 9621G































































































Reviews:

No comments