manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 740 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 740

Manual upgrade of an existing S8300B and G700 to S8300C with R4.0

740 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

 

Restoring the 4600-series phone configuration file, if any

If you copied a 4600-series phone configuration file to the 

/var/home/ftp/pub

 directory prior to 

the upgrade, the customer should use ftp to restore the file to /var/home/ftp/pub. You should 
then restore it to the /tftpboot directory. However, before you restore the file, be sure you have 
downloaded the appropriate IP phone firmware.

1. At the Linux command line, type 

cd ~ftp/pub

, and press 

Enter

.

2. At the prompt, type 

cp 46xxsettings.txt /tftpboot

, and press 

Enter

.

The 4600-series phone settings file is now restored to the /tftpboot directory.

Upgrade the G700 firmware

This section describes how to upgrade firmware on the components of the G700, including the 
Media Gateway Processor (MGP), the P330 Stack Processor, and any installed media modules. 
Alternate methods to upgrade the G700 Media Gateway include using the Avaya Installation 
Wizard, the Upgrade Tool, or Software Update Manager.

Verifying the contents of the tftpboot directory

Before proceeding with the G700 firmware installation, you should check the /

tftpboot

 directory 

on the TFTP server to make sure the firmware versions match those listed in the planning 
documentation. If they do not, you must copy the correct firmware versions into the 

/tftpboot

 

directory using the following procedure:

1. Download the firmware files from the support Website to your laptop.

!

CAUTION:

CAUTION:

If you are a customer administrator, you might be required to access the 

Download Center

 Web site in order to download firmware. For instructions on 

setting up access to the Download Center, access 

http://support.avaya.com

 and 

click on the appropriate links.

2. Using the Web Interface on the S8300 Media Server, copy the firmware files from your 

laptop to the 

/var/home/ftp/pub

 directory on the S8300, or

Alternatively, you can "ftp" the files from your laptop to the 

pub

 directory.

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments