manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 703 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 703

On-site Preparation for the Upgrade

Issue 10.2 May 2007

703

 

To check for translation corruption 

1. At the SAT prompt, type 

newterm

 and press 

Enter

.

2. Enter your terminal type and press 

Enter

.

If you see the message, 

Warning: Translation corruption found

 

follow the normal escalation procedure for translation corruption before continuing the 
upgrade.

To save translations

1. At the SAT prompt, type 

save translation 

and press 

Enter

.

2. Under 

Command Completion Status

 you should see 

Success

.

To disable alarm origination

If alarm origination is enabled during the upgrade, unnecessary alarms will be sent to the 
Operations Support System (OSS) destination number(s). Even if you selected 

Suppress 

Alarm Origination

 when you logged in, alarm origination will be automatically re-enabled when 

the system reboots after the software upgrade. Use this procedure to prevent alarm origination 
from being re-enabled after reboot.

!

CAUTION:

CAUTION:

If you do not disable alarm origination, the system can generate alarms during 
the upgrade, resulting in unnecessary trouble tickets. 

1. Logoff the SAT session.

2. At the command prompt, type 

almenable -d n -s n

, where

-d n

 sets the dialout option to 

neither

 (number)

-s n

 disables SNMP alarm origination

Note:

Note:

Be sure to reset alarm origination after the upgrade.

3. Type 

almenable

 (without any options) to verify the alarm origination status. 

You should see:

incoming: enable

Dial Out Alarm Origination: neither

SNMP Alarm Origination: n

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments