manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 686 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 686

Manual upgrade of an existing S8300B and G700 to S8300C with R4.0

686 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

 

!

CAUTION:

CAUTION:

When you are upgrading the media server as a primary controller, you must 
check 

Latest Communication Manager Software & Firmware Compatibility 

Matrix

 for the supported upgrade paths. If you attempt to upgrade the media 

server to a release that is not supported as an upgrade path, you might corrupt 
the translations. 

Also, you must check 

Latest Communication Manager Software & Firmware 

Compatibility Matrix

 for compatibility of software loads between the primary 

controller and any LSPs or ESSs. If the software loads of the primary controller 
and the LSPs/ESSs are incompatible, then file synchronization between the 
primary controller and the LSPs/ESSs can cause translation corruption on the 
LSPs/ESSs.

To check the 

Latest Communication Manager Software & Firmware 

Compatibility Matrix

 from any computer, access 

http://support.avaya.com

. 

Select 

Downloads

 > 

Latest TN Circuit Pack, Media Server, and Media 

Gateway Firmware and Software Updates

 > 

Latest Communication Manager 

Software & Firmware Compatibility Matrix

.

The steps to manually upgrade an S8300 configured as an LSP are the same as the steps to 
upgrade an S8300 configured as the primary controller, with the following additional 
considerations:

●

The version of Communication Manager running on the LSP must be exactly the same as, 
or a later version that is compatible to, the version running on the primary controller. 

●

If upgrading both the primary controller and the LSP to the same release, you must 
upgrade the LSP first. Then, with Communication Manager turned off on the LSP, you 
upgrade the primary controller. 

Converting the integration of IA770 INTUITY AUDIX Messaging
from CWY1 to H.323

!

CAUTION:

CAUTION:

Communication Manager Release 4.0 does not support the CWY1 integration of 
IA770 INTUITY AUDIX Messaging. As a result, if the S8300 Media Server uses a 
CWY1 board to integrate the IA770 INTUITY AUDIX application, you must 
remove the current IA770 integration administration before the upgrade and then 
administer the integration to H.323 after the upgrade. 

For instructions on converting the integration to H.323, including the removal of existing 
administration, see 

Administering Media Servers to work with IA770

, 07-600788.

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments