Home
/
Avaya
/
G700
/
Installing And Upgrading

Avaya G700, Installing And Upgrading, Page: 660 / 808

Share

Page: 660 / 808

Avaya G700 Installing And Upgrading Download Page 660

Manual upgrade of an existing S8300B or S8300C and G700 to R4.0

660 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

11. Click

Close

.

You are returned to the main menu.

Note:

Note:

This Web session will be interrupted by the reboot that occurs during the primary
server upgrade. After the reboot, the links in the main menu of the Web interface
will not function. Therefore, you must close and reopen the Web browser to
continue with the upgrade procedure.

12. Close the Web browser.

13. Reopen the Web browser and log in.

14. Under Server, click

Software Version

to verify the new software version.

!

Important:

Important:

After upgrading an S8300, you must upgrade the G700 or G350 and media
module firmware before restarting IA770.

Installing updated authentication files

!

CAUTION:

CAUTION:

A super-user login, dadmin or another customer superuser login, must exist

before

you install an authentication file. If the authentication file does not install,

you might need to create a super-user login, then install the new authentication
file. See

Ensuring a super-user login exists

To install the license and authentication files:

1. On the Maintenance Web Interface menu under Security, select

License File

.

The

License File

screen displays.

«
...
658
659
660
661
662
...
»

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments