Home
/
Avaya
/
G700
/
Installing And Upgrading

Avaya G700, Installing And Upgrading, Page: 623 / 808

Share

Page: 623 / 808

Avaya G700 Installing And Upgrading Download Page 623

Before going to the customer site

Issue 10.2 May 2007

623

●

Installing new firmware on the G700 Media Gateway Processor

●

Installing new firmware on the media modules

●

Installing new firmware on other G700 media gateways

Post-upgrade tasks

●

Installing IA770 service pack (or RFU) files, if any

●

To check media modules

●

To enable scheduled maintenance

●

To busy out trunks

●

To check for translation corruption

●

To resolve alarms

●

To re-enable alarm origination

●

Backing up the system

Before going to the customer site

The procedures in this section should be completed before going to the customer site or before
starting a remote installation.

Obtaining a USB DVD/CD-ROM drive

Upgrading Communication Manager on an S8300 to release 4.0 requires remastering the
S8300B/C hard drive. After remastering the drive, the remastering program looks for the
Communication Manager software files on an external USB CD-ROM drive (S8300B or
S8300C). Therefore, you must have a USB DVD/CD-ROM drive at the site.

Getting information that the project manager provides

Ask the project manager for the information needed to prepare for this installation.

B: Information checklists

provides several checklists to help you gather the installation and

upgrade information.

«
...
621
622
623
624
625
...
»

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments