Home
/
Avaya
/
G700
/
Installing And Upgrading

Avaya G700, Installing And Upgrading, Page: 619 / 808

Share

Page: 619 / 808

Avaya G700 Installing And Upgrading Download Page 619

Issue 10.2 May 2007

619

Chapter 11: Manual upgrade of an existing S8300B or

S8300C and G700 to R4.0

This chapter covers the procedures to upgrade the software on an installed Avaya S8300B or
S8300C Media Server from a 2.x or 3.x release to 4.x. The procedures to upgrade the G700
firmware use CLI commands instead of the Upgrade Tool. This chapter also covers the
procedures to upgrade the firmware on an installed Avaya G700 Media Gateway.

!

Important:

Important:

This chapter assumes that the currently installed S8300 is version B or C. The
S8300B is required to run Communication Manager release 2.0 or greater. The
S8300C is required to run Communication Manager release 4.0. If the currently
installed S8300 is version A, follow the upgrade procedures in

10: Manual upgrade of an S8300A and G700 to R4.0

Considerations for upgrading the S8300B or S8300C as a
primary controller or as an LSP

The S8300 can be configured as either the primary controller or as a local survivable processor
(LSP). When the S8300 is an LSP, the primary controller, running Avaya Communication
Manager, can be either another S8300 or an S8400, S8500, or S8700-series Media Server.

«
...
617
618
619
620
621
...
»

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments