manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 613 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 613

Post-upgrade tasks

Issue 10.2 May 2007

613

 

To "session" over to another G700/P330/C360 in a stack

1. At the 

MG-001-1(configure)#

 

prompt, type 

session stack

The 

P330-1(configure)#

 prompt appears.

2. At the

 P330-1(configure)#

 

prompt, type 

session 

<mod_num>

 

mgp

where

 <mod_num>

 is the next P330 or C360 processor in the stack. 

If you are currently logged in to the master stack processor, 

<mod_num>

 would be

 2

, for 

the second G700/P330/C360 processor in the stack.

3. For other G700s in the stack, repeat the steps described previously to install firmware for 

the stack processor, MGP, and media modules. 

Installing G700 firmware in a remote, no stack configuration

If additional G700 media gateways are supported in the configuration, but they are not attached 
as a stack, then you must configure each G700, with all of its devices, including the P330 
processors. Additionally, you must check firmware and update the firmware as required.

Post-upgrade tasks

Complete the following tasks after you have finished the upgrade:

Stopping IA770 INTUITY AUDIX Messaging, if installed

After the upgrade is complete, perform the following post-upgrade tasks.

1. From the 

Maintenance Web Page

, select 

Messaging Administration

 from the 

Miscellaneous

 menu.

The 

Messaging Administration

 Web page is displayed in a new Web browser window.

2. From the 

Messaging Administration

 Web page, select 

Utilities

.

The 

Utilities

 Web page is displayed.

3. Select 

Stop Messaging Software

.

The 

Stop Messaging Software

 Web page is displayed.

4. Select the 

Stop

 button.

The shutdown of the messaging server will begin once all users have logged off from IA 
770. Once the server has been stopped, the Web page will display status information. Once 
this process has begun, it will take a few minutes to complete the shutdown.

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments