manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 494 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 494

Manual installation of a new G700 with an S8300

494 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

 

If using IA770, administer Communication Manager for 
Integrated Messaging

A number of administration tasks must be performed to allow IA770 Integrated Messaging to 
work. These tasks are explained in detail in 

Administering Media Servers to work with IA770

.

!

CAUTION:

CAUTION:

IA770 INTUITY AUDIX Messaging processes messages using the G.711 codec 
only. Therefore, ensure that a codec set exists that uses only the G.711 codec. 
Then, assign that codec set to a network region. And, finally, assign that network 
region to the AUDIX signaling group that is linked to the IA770 INTUITY AUDIX 
Messaging trunk group.

If IA 770 fails to start after a new installation

If you have installed or upgraded IA 770 INTUITY AUDIX and it does not start, you must ensure 
that an IP address has been provided for use with IA 770. To check for the IP address, you must 
use the 

Configure Server

 option through the Maintenance Web pages.

On the Configure Interfaces screen, ensure that a valid IP address is present in the 

Integrated 

Messaging

 section

.

Complete the Installation Process
(for an S8300 LSP)

Consult the planning documentation to obtain the necessary information to complete the 
installation. 

Part of the final process will be to: 

●

Connect and administer test endpoints

●

Test endpoints

●

Complete the electrical installation

●

Enable adjunct systems 

This completes the installation of the G700 Media Gateway with an S8300 LSP.

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments