Avaya G700 Installing And Upgrading Download | Manualshive

Page: 109 / 808

background image

About installation and cabling

Issue 10.2 May 2007

109

b. TST (S8300B) or APP (S8300C) - green – lights up, then turns off

c. ACT - yellow – lights up, then turns off

d. OK To REMOVE - green - lights up, then turns off

e. LEFT LED in SERVICES port - green (10 MB link speed) lights up, then turns off

f. LEFT LED in SERVICES port - yellow (100 MB link speed) lights up, then turns off

g. RIGHT LED in SERVICES port - green lights up, then turns off

When you first power up the S8300, the red Major Alarm LED lights. During startup,
self-tests run, after which all LEDs turn off. At this point, you can connect to the S8300.
When Communication Manager starts, the green TST/APP LED turns on and stays on.

5. Verify the following LED’s status:

- On the media modules: all LEDs are off.

Note:

Note:

If the initial administration of all media modules is not completed, an alarm LED
will light.

- The master LED (labeled MSTR) or the system LED (labeled SYS) lights on one and only

one module in the stack.

- On the G700 media gateway, the green CPU LED is illuminated, when both the P330

Stack Processor (Layer 2 Switching Processor) and the G700 Media Gateway Processor
(MGP) are in a normal operational state.

The red ALM LED lights whenever an alarm exists in the G700 Media Gateway Processor.
The ALM LED might signal either a hardware failure or a software or firmware condition that
could be cleared by resetting the processor. It will also light because the license file for the
S8300 has not yet been installed. For an S8300C only, the ALM LED flashes when the
BIOS is rebooted. If it does not stop flashing, then there may be a problem with the hard
drive. For an S8300C also, the ALM LED lights steadily when theS8300 has been
shutdown.

Checking and Connecting DC Power

Note:

Note:

Perform this check procedure only if you are installing a G700 that is using the
DC input-power option rather than AC input-power.

«
...
107
108
109
110
111
...
»

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for G700

Brand: Grandstream Networks Pages: 4

Modular IoT Gateway

Brand: Volansys Pages: 26

Brand: Cellio Pages: 9

Brand: Hypercom Pages: 2

Brand: digitalSTROM Pages: 27

Brand: Ursalink Pages: 25

Brand: Zte Pages: 13

Brand: Four-Faith Pages: 32

Brand: enphase Pages: 2

Brand: Ackcio Pages: 19

Brand: Juniper Pages: 150

Brand: TANDBERG Pages: 2

Brand: Oki Pages: 344

Brand: TCS Basys Controls Pages: 5

Brand: Sargent and Greenleaf Pages: 32

Brand: IPshop Pages: 13

Echolife HG520b

Brand: Huawei Pages: 33

EchoLife BM635 WiMAX CPE

Brand: Huawei Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands