manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 108 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 108

Hardware installation for the G700 Media Gateway and S8300 Media Server

108 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

 

3. Measure the AC voltages in the following order:

!

WARNING:

WARNING:

If the voltage readings do not measure the values given, the AC outlet is 
improperly wired — DO NOT INSTALL THE SYSTEM. Advise the customer to 
have a licensed electrician correct the problem.

Once the ground and voltages have been verified to be correct for the installation, you are now 
ready to power the system.

Plugging in AC power

To connect to AC power

1. Plug the power cord into the G700

2. Plug the power cord into the outlet that was tested. 

Note:

Note:

There is no On/Off power switch on the G700 Media Gateway. The AC inlet 
serves as the disconnect device. To disconnect power from the G700 Media 
Gateway, remove the power cord plug from the AC inlet.

The G700 Media Gateway powers up. The LEDs on the media modules, the S8300 Media 
Server, and the G700 Media Gateway flash at power-up. Each element conducts a series of 
self-tests.

3. The LEDs on the G700 LED panel flash, and the red ALM LED lights up until the self-tests 

on the G700 Media Gateway have completed.

4. The LEDs on the S8300 Media Server light as described in the following sequence:

a. ALM - red - lights up, then turns off. 

For an S8300C only

, during the BIOS boot, the ALM 

LED is on (not flashing). When the BIOS boot finishes, the ALM LED starts flashing to 
indicate that all hardware diagnostics have passed and the system is ready to load the 
OS. The ALM LED continues to flash until the Avaya software is installed. The ALM LED 
turns off when the Avaya Linux drivers are installed.

Figure notes:

1. Phase to neutral should be 110 to 

125 Vac.

2. Neutral to ground should be less 

than 1 Vac.

3. Phase to ground should be 110 to 

125 Vac.

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments