manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

filter apply act <act-id>

Configuring ACLs

Configure access control lists (ACL) to create rules for the ACT.

 Important:

If an ACT contains IPv6 attributes, you must configure an ACL of pktType IPv6. If the ACT

uses only Ethernet attributes, you can configure one ACL of pktType IPv4 and an ACL of

pktType IPv6.

Prerequisites

You must log on to the Global Configuration mode in the ACLI.

Procedure steps

1. Configure an ACL by using the following command:

filter acl <acl-id> type <inVlan|outVlan|inPort|outPort> act
<act-id> pktType <ipv4|ipv6> name <word>

2. Enable an ACL by using the following command:

filter acl <acl-id> enable

Variable definitions

Use the data in the following table to use the 

filter acl

 command.

Variable

Value

acl-id

Specifies an ACL ID in the range 1–4096.

act <act-id>

Specifies the ACT ID to associate with the ACL.

enable

Enables the ACL state along with all ACEs below it.
Enable is the default state for the ACL.

name 

<word>

Renames an ACL. To configure this option to the
default value, use the default operator with the
command.

Configuring ACLs

Configuration — IPv6 Routing

November 2010     339

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

IBM 51 Troubleshooting Manual preview
51
Brand: IBM Pages: 248
Panasonic BB-HGW700A - Network Camera Router Installation/Troubleshooting Manual preview
BB-HGW700A - Network Camera Router
Brand: Panasonic Pages: 10
Wave wifi EC Series Quick Start Manual preview
EC Series
Brand: Wave wifi Pages: 2
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Brand: Rabbit Pages: 126
4Home ControlPoint 2000 User Manual preview
ControlPoint 2000
Brand: 4Home Pages: 20
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
Patton electronics IPLink 2802 Specifications preview
IPLink 2802
Brand: Patton electronics Pages: 2
Lanner NCA-1525 User Manual preview
NCA-1525
Brand: Lanner Pages: 78
Cowfish Technologies VanConnect User Manual And Installation Manual preview
VanConnect
Brand: Cowfish Technologies Pages: 38
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
BHU NETWORKS BXM2 User Manual preview
BXM2
Brand: BHU NETWORKS Pages: 75
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
Comet Labs 24-Port 1000BASE-T User Manual preview
24-Port 1000BASE-T
Brand: Comet Labs Pages: 44
Hanwha Techwin Wisenet XRN-6410RB2-24TB User Manual preview
Wisenet XRN-6410RB2-24TB
Brand: Hanwha Techwin Pages: 124
3Com Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface... Quick Manual preview
Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...
Brand: 3Com Pages: 12
Enterasys 2H258-17R Installation & User Manual preview
2H258-17R
Brand: Enterasys Pages: 62

Brands by name

Popular brands

Load more brands