manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Parameter

Description

BACKUP MASTER
STATE

Indicates the state of the backup master router.

FAST ADV INTERVAL

Indicates the time interval, in milliseconds, between sending
Fast Advertisement messages. When the Fast Advertisement
Interval is enabled, the Fast Advertisement Interval is used
instead of the regular advertisement interval.

FAST ADV ENABLE

Indicates the Fast Advertisement Interval status.

Clearing IPv6 VRRP statistics

Use the following procedure to clear IPv6 VRRP statistics.

Procedure steps

1. To clear global IPv6 VRRP statistics, enter:

clear ipv6 vrrp

2. To clear IPv6 VRRP statistics on a particular port, enter:

clear ipv6 vrrp ports <ports> vrid <value>

3. To clear IPv6 VRRP statistics on a particular VLAN, enter:

clear ipv6 vrrp VLAN <vid> vrid <value>

Variable definitions

Use the data in the following table to use the 

clear ipv6 vrrp

 command.

Variable

Value

<ports>

Specifies the port value.

<vid>

Indicates the VLAN ID in the range of 1 to 4094.

vrid <value>

A unique integer value that represents the virtual
router ID in the range 1 to 255. The virtual router acts
as the default router for one or more assigned
addresses.

Clearing IPv6 VRRP statistics

Configuration — IPv6 Routing

November 2010     237

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
Vanguard 342 Quick Reference Manual preview
342
Brand: Vanguard Pages: 4
Draytek VigorIPPBX 2820 Series Quick Start Manual preview
VigorIPPBX 2820 Series
Brand: Draytek Pages: 29
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne Hotwire 6301 Installation Instructions Manual preview
Hotwire 6301
Brand: Paradyne Pages: 20
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
IBM TotalStorage SAN16M-R SAN Installation And Service Manual preview
TotalStorage SAN16M-R SAN
Brand: IBM Pages: 116
Konig CMP-HOMEPL1000 Manual preview
CMP-HOMEPL1000
Brand: Konig Pages: 73
Ruckus Wireless SmartZone 3.6 Command Reference Manual preview
SmartZone 3.6
Brand: Ruckus Wireless Pages: 102
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
ZyXEL Communications VMG5313-BXB SERIES Quick Start Manual preview
VMG5313-BXB SERIES
Brand: ZyXEL Communications Pages: 2
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
Airlink101 AWMB100 User Manual preview
AWMB100
Brand: Airlink101 Pages: 46
ATTO Technology iPBridge 2500C Specifications preview
iPBridge 2500C
Brand: ATTO Technology Pages: 2
ADTRAN ENHANCED PSD 239 H2R Product Manual preview
ENHANCED PSD 239 H2R
Brand: ADTRAN Pages: 2
Enterasys X-Pedition XSR-1850 Getting Started Manual preview
X-Pedition XSR-1850
Brand: Enterasys Pages: 114
N-Tron 304TX-N Specifications preview
304TX-N
Brand: N-Tron Pages: 2
Belkin F5D7230au4P Manual preview
F5D7230au4P
Brand: Belkin Pages: 2

Brands by name

Popular brands

Load more brands