manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

7. Click 

Enabled

 to enable DHCP relay. You can enable or disable each agent server

forwarding path. The default is enabled.

8. Click 

Insert

.

Variable definitions

Use the data in the following table to configure the DHCP Relay forward path.

Variable

Value

AgentAddr

The IP address of the input interface (agent) on which the DHCP request
packets are received for forwarding. This address is the IP address of
either a brouter port or a VLAN for which forwarding is enabled.

ServerAddr

This parameter is the IP address of the DHCP server. The request is
unicast to the server address.

Enable

Enables DHCP relay on the routing switch.

Configuring DHCP relay interface parameters

Configure the DHCP relay behavior on the interface.

Procedure steps

1. In the navigation tree, open the following folders: Configuration, IPv6.

2. Double-click 

DHCP Relay

.

3. In the Interface tab, click Insert.

4. Enter the appropriate values.

5. Click 

Apply

.

Variable definitions

Use the data in the following table to configure the DCHP Relay interface parameters.

IPv6 DHCP Relay configuration using Enterprise Device Manager

196     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

4RF Aprisa LTE Quick Start Manual preview
Aprisa LTE
Brand: 4RF Pages: 7
Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
Cowfish Technologies VanConnect User Manual And Installation Manual preview
VanConnect
Brand: Cowfish Technologies Pages: 38
IMC Networks iMcV-FiberLinX Operation Manual preview
iMcV-FiberLinX
Brand: IMC Networks Pages: 36
Perle IOLAN MDC User Manual preview
IOLAN MDC
Brand: Perle Pages: 491
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
Ethernet Direct Husky HMG-1648EP User Manual preview
Husky HMG-1648EP
Brand: Ethernet Direct Pages: 16
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
ActionTec GE344000-01 User Manual preview
GE344000-01
Brand: ActionTec Pages: 87
R.V.R. Elettronica PTX30-UHT Installation, Technical And Maintenance Manual preview
PTX30-UHT
Brand: R.V.R. Elettronica Pages: 171
Thecus N5200BR User Manual preview
N5200BR
Brand: Thecus Pages: 90
Multitech ROUTE FINDER RFIPSC-1 Quick Start Manual preview
ROUTE FINDER RFIPSC-1
Brand: Multitech Pages: 54
Samsung MagicLAN SWL-2000P User Manual preview
MagicLAN SWL-2000P
Brand: Samsung Pages: 62
Tripp Lite N306-010 Specification Sheet preview
N306-010
Brand: Tripp Lite Pages: 2
Addi-Data MSX-E Series Technical Description preview
MSX-E Series
Brand: Addi-Data Pages: 20
Cambium Networks PTP 820C HP Installation Manual preview
PTP 820C HP
Brand: Cambium Networks Pages: 227
Junxion Junxion Box JB-110b User Manual preview
Junxion Box JB-110b
Brand: Junxion Pages: 48
Supermicro SSE-G24-TG4 Stacking Manual preview
SSE-G24-TG4
Brand: Supermicro Pages: 16

Brands by name

Popular brands

Load more brands