manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

config ethernet

 

<slot/port>

 

ipv6 create addr

 

<ipv6 address>

 

vlan

 

<vlan id>

Variable definitions

Use the data in the following table to use the 

config ethernet ipv6 create addr vlan

command.

Table 8: Variable defintions

Variable

Value

ipv6 address

Specifies the IPv6 address to add to the port.

slot/port

Identifies the slot and port location.

vlan id

Specifies the ID of the VLAN, from 1-4094.

Setting the administrative status on a brouter port

Enable the brouter port by setting the administrative status.

Procedure steps

Configure the administrative status by using the following command:

config ethernet

 

<slot/port>

 

ipv6 admin enable

Variable definitions

Use the data in the following table to use the 

config ethernet ipv6 admin enable

command.

Variable

Value

slot/port

Specifies the slot and port location for the
port.

Basic IPv6 configuration using the CLI

104     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
H3C H3C S7500E-X Command Reference Manual preview
H3C S7500E-X
Brand: H3C Pages: 16
H3C SR6600 SPE-FWM Configuration Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 24
Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
Paradyne Adapter Bracket Notice preview
Adapter Bracket
Brand: Paradyne Pages: 1
H3C S10500 Series Mpls Configuration Manual preview
S10500 Series
Brand: H3C Pages: 400
Multitech MultiConnect SE MTS2EA Specification Sheet preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 2
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Matrix Switch Corporation MSC-1HD1608L Product Manual preview
MSC-1HD1608L
Brand: Matrix Switch Corporation Pages: 60
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
ADDON ARM8100 Quick Installation Manual preview
ARM8100
Brand: ADDON Pages: 4
SMC Networks SMC-EZ1026DT User Manual preview
SMC-EZ1026DT
Brand: SMC Networks Pages: 56
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
rtd IDAN-ID5915 User Manual preview
IDAN-ID5915
Brand: rtd Pages: 28
Patton electronics OnSite 9100 Quick Start Manual preview
OnSite 9100
Brand: Patton electronics Pages: 8
PC Concepts Full-Rated Router ADSL2+ User Manual preview
Full-Rated Router ADSL2+
Brand: PC Concepts Pages: 104

Brands by name

Popular brands

Load more brands