Avaya DEFINITY Server R Manual Download Page 288

Page: 288 / 550

Upgrading a Multicarrier G2 Universal Module to Avaya
DEFINITY Server R EPN running Avaya Communication
Manager

555-233-115

5-98

Issue 7 November 2003

Figure 5-18.

Collocated Fiber Optic Connections EPN1 to EPN2

For Either One or Two Fiber-Remoted Expansion Port Networks

1. At control carrier A of PPN cabinet 1. See

Figure 5-15

through

Figure 5-19

■

Install a lightwave transceiver on the cable connector at slot 1A01.

NOTE:

Attenuators may be required for single mode fiber using a
300A Lightwave Transceiver

■

Connect a fiber optic cable to the transceiver just installed.

■

Route the cable to the cable tray and down, out of the cabinet,
through the cable manager to the PDS cross-connect facility.

■

Connect the fiber cable to the lightguide interconnect unit provided.

■

Carefully attach the cable (with cable ties) to the wall of the cable
tray at the built-in cable tie positions.

2. Behind control carrier A of EPN cabinet 2:

■

Install a lightwave transceiver on cable connector at slot 2A01.

NOTE:

Attenuators may be required for single mode fiber using a
300A Lightwave Transceiver

■

Connect a fiber optic cable to the transceiver just installed.

Figure Notes

1. Lightwave Transceiver

2. To PPN Carrier A Slot 2A02

3. To EPN 1 Carrier A Slot 3A02

4. Fiber Optic Cable

5. TX Connector

6. RX Connector

cydff05 CJL 103196

RX TX

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands