Avaya DEFINITY Server R Manual Download Page 213

Page: 213 / 550

Remove Module Control Carrier(s)

Issue 7 November 2003

5-23

555-233-115

Figure 5-1.

TDM/LAN Connections for Control Module (Standard Reliability)

Figure Notes

1. Port Carrier (“C” Position)

2. ZAHF4 TDM/LAN Terminator

3. TDM/LAN Cable (WP91716 L6)

4. Module Control Carrier (“A” Position)

5. Port Carrier (“D” Position)

6. Port Carrier (“E” Position)

7. Slot 21

8. Slot 01

9. TDM/LAN Cable (WP91716 L7)

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands