Avaya DEFINITY SERIES Installation And Maintenance Manual Download Page 32 | Manualshive

Page: 32 / 101

Avaya DEFINITY SERIES Installation And Maintenance Manual Download Page 32

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN

555-233-121

Issue 2

November 2000

SREPN Installation

1-12

Connect cables to the SRP

1

Connect cables to the SRP

The TN2301 survivable remote switch circuit pack is located in slot 7 of the SRP
cabinet. Fiber optic transceivers are attached to the TN2301 circuit pack. Fiber
cables are connected from these transceivers to the TX and RX connectors on the
rear of the cabinet.

NOTE:

Always connect a fiber cable from a TX connector to an RX connector and
vice versa.

Do not connect the cables to the EPN until you reach the

‘‘Replace EPN

circuit packs and make cable connections’’

section.

Depending on the customer’s configuration, refer to one of the following sections
for connecting fiber cables to the SRP:

■

Connect SRP fiber cables for standard/high reliability

■

Connect SRP fiber cables for critical reliability

Connect SRP fiber cables for standard/high
reliability

1. Connect the equipment as shown in

Figure 1-5 on page 1-13

.

2. Go to the

‘‘Connect the SRP and Management Terminal’’

section.

Connect SRP fiber cables for critical reliability

1. Connect the equipment as shown in .

2. Go to the

‘‘Connect the SRP and Management Terminal’’

section.

«
...
30
31
32
33
34
...
»

Summary of Contents for DEFINITY SERIES






































































































Reviews:

No comments