manualshive.com logo in svg

Avaya BSGX4e, Installation Manual

Share
Download
Avaya BSGX4e Installation Manual Download Page 36

BSGX4e Business Gateway Installation Guide

36

Release 01.01

NN47928-303

Figure 8. Upgrade Tab

3. In the upper half of the Software tab, select the software to be upgraded:

n

Slot 1

 and 

Slot 2

 represent the application software images that are present in 

the BSGX4e.

Note: 

The slot that is upgraded is automatically set as the default image that is 

run when the device restarts. (The default image can be changed after the 
upload.)

n

Bootloader

 represents the application that loads the new image at restart.

4. In the 

Load File

 text box, enter the software file to upload. 

If necessary, press 

Browse

 to locate the file on the workstation.

5. Click 

Upgrade

.

Messages are displayed as the upgrade steps complete.

6. When the upgrade is complete, the message 

Updating Successful

 appears.

IMPORTANT: 

Do not reboot before the Updating Successful message appears.

7. To reboot the unit and put the upgraded software into use, select the 

Reload 

System 

button in the Operations menu in the lower left of the screen. See 

Figure 9.

Click the image to upgrade.

Click 

Browse

 to find 

the upgrade file.

Click 

Upgrade

 to start the upload.

Summary of Contents for BSGX4e

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands