Avante FURMDKAVNAH12 User Manual Download Page 11

Page: 11 / 12

Motorised Height Adjustable Desk

E&OE

Cleaning and Troubleshooting

Some maintenance activities described may be beyond the scope of some users. For

procedures that you are not comfortable with or have the tools, knowledge or experience for,

have the unit serviced by a service centre or qualified technician.

Cleaning

The desk can be cleaned with a soft cloth. Do not use abrasives, solvents or harsh chemicals. Be careful not

to get excessive moisture on the display panel as this may damage it and create an electrical hazard.
Keep the equipment out of direct sunlight to prevent damage to surface finishes.

Troubleshooting

The following information may assist in identifying a problem and rectifying it.

Problem

Potential Reason

Correction

Desk not responding to

control panel or "E01"

or "E02" shown on

control panel

. No electrical supply.

. Cables not properly

connected.

. Motor "duty cycle"

exceeded.

. Connect unit to mains 240VAC electrical supply and switch

supply ON.

. Ensure that motor control module cables are properly

connected and are undamaged.

. Wait at least 20 minutes to allow motor to cool before trying

again.

Slow upward

movement

Overloaded.

Ensure that total weight of all items on the desk does not

exceed 80kg.

Motor runs, but no

movement, or

downward only

movement

. Overloaded.

. Drive links installed

incorrectly.

. Ensure that total weight of all items on the desk does not

exceed 80kg.

. Ensure that the drive links are

installed

so that the motor

drive shaft and gearbox are fully engaged with the drive links.

Desk lowering by itself

or "E03" or "E04"

shown on control panel

Overloaded.

Ensure that total weight of all items on the desk does not

exceed 80kg.

Reset

the desk.

Desk continuously

resetting

Overloaded.

Ensure that total weight of all items on the desk does not

exceed 80kg.

Reset

the desk.

Desk not moving to

correct pre-set height

. Reset required.

. Settings corrupted.

Reset

the desk, then try again.

. Reset to factory defaults to erase all pre-set heights – press

and

together and hold until the desk beeps twice.

Reset

the desk, then

set pre-set heights

again.

"E05", "E06" or "E10"

shown on control panel

Reset required.

Reset

the desk.

"E07" or "E08" shown

on control panel

Poor motor control

module connections.

Check all connections to and from the motor control module

are clean and well connected.

Reset

the desk.

When to Call for Help

If after resetting the desk that it is still not operational, call an authorised service centre or technician for

servicing.

Specifications

Electrical

240VAC / 50Hz

Weight Capacity

80kg

ANTE

Summary of Contents for FURMDKAVNAH12













Search results

Summary of Contents for FURMDKAVNAH12

Reviews:

Avante FURMDKAVNAH12, User Manual, Page: 11 / 12

Search results

Summary of Contents for FURMDKAVNAH12

Reviews: