Output protocols
Wiegand or RS485
Power requirement
8VDC to 16VDC (nominal operating voltage 12VDC)
Current
consumption
60
mA (Av
erage
)
160
mA (Peak)
Read range
20
mm to
40mm (0.8”
to
1.6”) at 12VDC
depends on the type of card
used
Operating
temperature
-25
°
C to +65
°
C (-13
°
F to
+
149
°
F)
Relative humidity
90% max, operating non-condensing
Reader dimensions
AU Perplex plate
(BT510)
116mm(L) x 84mm(W) x 26mm(D) (4.57”
x
3.31”
x
1.02”)
UK Perplex plate
(BT511)
116mm(L) x 80mm(W) x 26mm(D) (4.57”
x
3.15”
x
1.02”)
Status LED
Green & Red
Audible tone
Internal and external buzzer control
Colour finish
Charcoal
IP rating
IP65
Wiring diagram
Note:
•
A shielded cable is recommended to be used. The shield is connected to controller 0V reference
•
Maximum wiegand data cable length: 150 meters (500 feet)
•
Buzzer and LED are low activated.
•
RS485 lines are only for optional use.
•
Insulate all un-used wires (do not terminate).
Regulatory Information
C-Tick
: This device is C-Tick complied.
CE
: The device has passed all relevant tests and obtained CE approval.
FCC
: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device
may not cause interference and 2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate this
equipment.
Warranty
Unless specified otherwise, the Company warrants to the Customer that’ BQT Solutions Branded
Products’ (excluding third party products and software) are covered by a return to base warranty on
defects in materials and workmanship affecting normal use for a period of the Warranty offered under
the Standard Terms and Conditions of Sale from BQT invoice date (‘Standard Warranty’)
This standard warranty does not cover damage, fault, failure or malfunction due to external causes
including; accident, misuse, problems with electrical power, servicing not authorised by the Company,
usage and/or storage and/or installation not in accordance with Product instructions, failure to perform
required preventative maintenance, normal wear and tear, act of God, fire, flood, war, any violent or
similar occurrence; any attempt by any person other than Company personnel or any person authorised
by the Company to repair or support the Products and problems caused by use of parts and
components not supplied by the Company. The standard warranty does not cover any items that are in
one or more of the following categories: software; external devices; accessories or parts added to the
product after the product has been shipped from BQT Solutions.
During the warranty, period beginning on the invoice date, the Company will repair or replace faulty
products (at its absolute discretion) returned to its’ factory. The Customer must prepay shipping and
transportation costs and insure the shipment or accept the risk of loss or damage during such
transportation.
The Customer shall be solely responsible for determining suitability for use and the Company will, in no
event, be liable in this respect. This standard warranty is given in place of all warranties, conditions,
terms, undertakings and obligations implied by statute, common law, trade usage, and course of
dealing or otherwise including warranties or conditions of merchantability, fitness for purpose,
satisfactory quality and / or compliance with description, all of which are hereby excluded to the fullest
extent permitted by law.
BT
510
INSTALLATION GUIDE
Rev 002
Specifications
© 2015 BQT Solutions (Australia) Pty Limited. All rights reserved.
BQT Solutions (Australia) Pty Limited will not be liable for any direct, indirect, incidental or
consequential loss or
damage in any way related to this product. BQT Solutions (Australia)
Pty Limited reserves the right to upgrade or
change this product or instruction manual
without prior notice. BQT Solutions (Australia) Pty Limited assumes no
liability for damages
incurred directly or indirectly from errors, omissions or discrepancies between the product
and the manual.
The product is designed by BQT Solutions (Australia) Pty Limited.
For more information and contact details please visit,
www.bqtsolutions.com
