Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power / Ground
cable size
It is critical to use the proper
power and ground cable. Select
the size listed here for your
amplifier model. Always use high
quality copper cable.
Cable size recommendations for
multi amp systems are available
on our website.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
Bare metal
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplifier
Signal Input
Low Level RCA
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
6
9
10
4
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
7
9V
0.2V
INPUT
LEVEL
6V
0.2V
LEVEL
PHASE
0
180
BASS EQ
0
10dB
BASS EQ
0
9dB
BASS EQ
0
12dB
15
35Hz
SUBSONIC
10
40Hz
SUBSONIC
30
250Hz
LPF
35
250Hz
LPF
40
300Hz
LPF
FULL
LP
HP
XOVER
MONO STEREO
MODE
FULL LPF HPF
XOVER
MONO STEREO
MODE
4CH
2CH
MODE
60
1.3KHz
HPF
60
1.2KHz
HPF
10
2.5KHz
HPF
10
1.5KHz
HPF
4ga
Model Fuse Size Cable Size
MM-1125.1D
MM-1525.1D
MM-2025.1D
MM3025.1D
MM-4025.1D
MM-1525.2D
MM-2025.2D
MM-3025.2D
MM-1525.4D
MM-2025.4D
MM-3025.4D
MM-1525.5D
External 60A
External 60A
External 80A
External 125A
External 150A
External 50A
External 100A
External 150A
External 40A
External 60A
External 80A
External 100A
Using spade terminals, connect the
+12V to the power cable from the
battery, the REM to the source unit
turn-on wire and the GND to the
chassis ground..
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best fits your
speaker configuration.
Power
Connections
Speaker
Connections
Stereo
Monoblock
single woofer
Monoblock
multiple woofers
Bridged
5
8
SPEAKER
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
CH2
CH1
BRIDGED
SPEAKER
OUTPUT
CH4
CH3
BRIDGED
SPEAKER
OUTPUT
SPEAKER
CH4
CH3
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
CH2
CH1
BRIDGED
SPEAKER
OUTPUT
CH4
CH3
BRIDGED
SPEAKER
OUTPUT
SPEAKER
CH4
CH3
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
CH2
CH1
BRIDGED
SPEAKER
OUTPUT
CH4
CH3
BRIDGED
SPEAKER
OUTPUT
SPEAKER
CH4
CH3
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
RIGHT
LEFT
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
CH2
CH1
BRIDGED
SPEAKER
OUTPUT
CH4
CH3
BRIDGED
SPEAKER
OUTPUT
SPEAKER
CH4
CH3
BRIDGED
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
