manualshive.com logo in svg

Autonics PMC-1HS Series, Instruction Manual, Page: 60 / 82

Share
Download
Autonics PMC-1HS Series Instruction Manual Download Page 60

6. Drive by Teaching Unit

59

© Copyright Reserved Autonics Co., Ltd.

6.2.2 

JOG operation

The JOG operation in the teaching unit is the operation to drive in the specified direction only when a button 

is pressed� In addition, the drive speed can be changed�

Yellow letter mark

Input button

Operation

X +

6

JOG shift in the + direction on X-axis  

X -

7

JOG shift in the - direction on X-axis

Y +

1

JOG shift in the + direction on Y-axis

Y -

2

JOG shift in the - direction on Y-axis

X SPD

8

Whenever these buttons are pressed, the drive speed is 

changed among 0 to 4�

The drive speed 1 to 4 output the values configured by REG 

79 to 82 and the drive speed 0 outputs the single pulse� If 

you press first, the currently registered speed is displayed. If 

you press continuously, the speed is changed�

Y SPD

3

6.2.3 

Execution of Operation Program

The registered operation program is carried out from the specified register number. The program can 

operate only X-axis, Y-axis or both of X and Y simultaneously. It is not allowed to execute Y-axis on 

operating X-axis, or vice versa. The procedure to execute the program is listed in the table below.

Order Input Procedure

Operation

1

Press the [EXC] button.

Executing a program

2

Select an axis by pressing

the [X/Y] button.

If the [X/Y] button is pressed, X-axis, Y-axis and X/Y-axis is selected 

in turn�

3

Input register numbers�

Input the number of the start register between 0 to 63�

4

Press the [EXC] button.

The program is executed from the inputted start register�

E.g.)To execute X-axis from REG10.

[EXC] → [X/Y] → [1] → [0] → [EXC]

To stop the program execution in operating, press the [STOP] button on each axis� In running, the 

current position on the selected axis is displayed. In other words, if X-axis or Y-axis is operating, the 

current position on X-axis or Y-axis is displayed respectively.
If X/Y-axis is operating, the current on X-axis is displayed. Once the program is running, you can 

monitor the current position by selecting an axis by means of the [X/Y] button.

Summary of Contents for PMC-1HS Series



















































































Reviews:

No comments