manualshive.com logo in svg

Autonics PMC-1HS Series, Instruction Manual, Page: 59 / 82

Share
Download
Autonics PMC-1HS Series Instruction Manual Download Page 59

6. Drive by Teaching Unit

58

© Copyright Reserved Autonics Co., Ltd.

6.1.5 

Index Drive

Execute the command of the register displayed in the data mode is executed once�

If you press the [EXC] button after selecting an axis via the [X/Y] button, the command of the register 

currently displayed is executed� However, the executable commands are limited as ABS, INC, OUT, OTP 

and HOM1 to 4. Other commands are not executed by pressing the [EXC] button. This function is normally 

executed for only one axis. However, if ABS, INC and HOM1 to 4 commands are configured as Both for 

X-axis, the commands are simultaneously executed for X/Y-axis by the input of the [EXC] button on X-axis.

6.2 

Drive operation

In drive handling mode, you can carry out JOG movement, Home Search and program execution�
REG displays dp in the drive handling mode� When a register number is displayed, press the [DP] button to 

convert into the mode� In the mode, Data displays the current position of the selected axis�

The button to handle is displayed in yellow letters on the left or the top of the input buttons and the higher 

end and the lower end of the buttons are used to handle X-axis and Y-axis respectively. The yellow letters 

above the input button describes each function� However, the [DP] button only has the data edit/drive 

handling change function�

6.2.1 

Home Search

The buttons to carry out the home search are listed in the table below�

Yellow Letter Displayed

Input button

Operation

X HOME

5

Home search on the X-axis

Y HOME

0

Home search on the Y-axis

Both of X and Y axes can be simultaneously handled.

If you stop the operation, press the [STOP] button of each axis�

Caution  

If the operation mode, parameter and home search mode should be configured before executing the home 

search� It may cause that the home search is not performed correctly�

D P

1 2 5 0 3

X ●
Y ●

Position data of the selected axis

Button display to

operate the drive

Input 

buttons

Summary of Contents for PMC-1HS Series



















































































Reviews:

No comments