manualshive.com logo in svg

Autonics PMC-1HS Series, Instruction Manual, Page: 55 / 82

Share
Download
Autonics PMC-1HS Series Instruction Manual Download Page 55

6. Drive by Teaching Unit

54

© Copyright Reserved Autonics Co., Ltd.

6.1.3 

Input of the Operation Program

The operation program is registered at registers number 00 to 63�
Each command and input method in the teaching unit are listed in the table below�

Comm 

-and

Display

Input method
Input operation

Description

ABS

INC

ABS

INC

Mode

ABS display

INC display

Absolute position

Relative position

ABS/INC

configuration

0: INC, 1: ABS

Drive Speed 1, 2, 3, 4

Post Timer 0, 1, 2, 3

End P 0: OFF, 1: ON

Both 0: OFF, 1: ON

A

1 8 0 0

- 7 3 0 0

) ) ! ! )

The selected mode is lighted in mode display

1 Press the [WRT] 

button�

The ABS display 

is flickered in the 

command input state�

2

Select a command

using the [↑] or [↓] 

button�

ABS display: ABS

INC display: INC

3 Press the [WRT] 

button�

The command is 

confirmed.

4 Input position data

(Input in pulse unit)

A sign is entered by 

pressing the [+/-] 

button�

5 Press the [WRT] 

button�

Its position data is 

confirmed and its mode 

is displayed�

6

Configure each 

mode by means of 

the [+/-] button and 

the [ ] button� 

[+/-] button: The 

flickering value is 

changed�

[ ] button: The selected 

item is moved� 

7 Press the [WRT] 

button�

The position data 

flickers twice to inform 

the completion of the 

registration�

HOM

The HOM command selects HOM1 to HOM4

depending on Enable/Disable configuration of

End P and Both�

Display

End P Both

HOM1

H O M 1

Disable Disable

HOM2

H O M 2

Enable Disable

HOM1

H O M 3

Disable Enable

HOM1

H O M 4

Enable Enable

1 Press the [WRT] 

button�

The ABS display 

is flickered in the 

command input state�

2

Select a command

using the[↑] or [↓ ]

button�

Select HOM1 to HOM4.

3 Press the [WRT] 

button�

The display flickers 

twice to inform the 

completion of the 

registration�

Caution  

HOM 3 and 4 cannot be selected for Y-axis.

JMP

REP

TIM

JMP

JMP

TIM

REG to jump

Repetition count

Time configuration

J M P

0 9

R E P

1 2 3

`

M

3 0 0

1 Press the [WRT] 

button�

The ABS display 

is flickered in the 

command input state�

2

Select a command

using the [↑] or [↓] 

button�

3 Press the [WRT] 

button�

The command is 

confirmed.

4 Input a value�

Input numbers are 

displayed from the right 

of the DATA

5 Press the [WRT] 

button�

The position data 

flickers twice to inform 

the completion of the 

registration�

Summary of Contents for PMC-1HS Series



















































































Reviews:

No comments