Autonics PMC-1HS Series Instruction Manual Download Page 52

Page: 52 / 82

6. Drive by Teaching Unit

© Copyright Reserved Autonics Co., Ltd.

6. Drive by Teaching Unit

The teaching unit (PMC-2TU-232) is a device that builds the operation mode parameter and operation

program for the main body without a PC� In addition, it can carry out the start of the operation program, the

home search and JOG operation�

The teaching unit is used by connection the private cable (1.5m) to the RS-232C connector (CN2) of the

main body�
It is recommended to select 9,600bps for more stable communication�

The teaching unit consists of data edit mode and drive handling mode� The data edit mode displays a

register number to the REG of the display part, and the drive handling mode displays dp (drive operation).
When turned on, it starts as the drive handling mode (dp display).

The [DP] button is used to convert the status of the data edit mode and the drive handling mode�

Mode

Operation

REG display

Data edit

• Adding operation mode parameter and operation program

• Index drive operation

Drive handling

• Displaying the current position

• JOG operation

• Home search

• Program execution

(drive operation)

PMC-2TU-232

connection cable

Summary of Contents for PMC-1HS Series



















































































Search results

Summary of Contents for PMC-1HS Series

Reviews:

Autonics PMC-1HS Series, Instruction Manual, Page: 52 / 82

Search results

Summary of Contents for PMC-1HS Series

Reviews: