manualshive.com logo in svg

Autonics AiC-D-20LA, User Manual

Share
Download
Autonics AiC-D-20LA User Manual Download Page 99

 

 

11 Driver Function 

ⓒ  Copyright Reserved Autonics Co., Ltd. 

 

99 

11

 

Driver Function 

11.1

 

General Drive 

11.1.1

 

Fixed Pulse and Continuous Pulse Drive 

Drive pulse output on each axis is basically in +/- directions by drive instruction of a fixed or 

continuous pulse. 

11.1.1.1

 

Fixed Pulse Drive 

Fixed pulse drive is used to move something a fixed amount. It operates fixed speed or 

acceleration/deceleration drive for a specified number of output pulses. 

Acceleration/Deceleration fixed pulse drive starts to reduce speed when remaining output 

pulse is less than the pulse used for acceleration. It ends drive when it finishes generating 

pulse, as shown in the image below. 

 

 

Absolute position movement and relative position movement 

: There are absolute position movement and relative position movement.   

  These are fixed pulse drive. 

 

 

Summary of Contents for AiC-D-20LA





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands