background image

MaxiSCR

13

the equipment.

NOTE

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:

‐‐

Reorient or relocate the receiving antenna.

‐‐

Increase the separation between the equipment and receiver.

‐‐

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

‐‐

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.

FCC WARNING STATEMENT

This equipment complies with FCC radiation exposure limits set forth for

Summary of Contents for MaxiSys SCR













Reviews: