manualshive.com logo in svg

Autel MaxiPRO MP808TS, Manual

Share
Download
Autel MaxiPRO MP808TS Manual Download Page 22

 

 

 

15 

NOTE 

The  shortcuts  buttons  will  be  highlighted  when  enabled,  and  dimmed 
when disabled. 

Table 3-3 

System Status Icons

 

Button 

Name 

Description 

 

Calculator 

Launches calculator when pressed. 

 

Clock 

Launches clock when pressed. 

 

BT 

Enables/disables BT when pressed. 

 

Wi-Fi 

Enables/disables Wi-Fi when pressed. 

 

Airplane 
Mode 

Enables/disables  Airplane  Mode  when 
pressed. 

 

System 
Settings 

Launches the Android System Settings 
interface when pressed. 

Powering Down 

All vehicle  communications must be terminated before  powering off the 
tablet.  A  warning message  will  display if  the  unit  attempts  to  power  off 
while still connected with the vehicle. Forcing the tablet to power off while 
the unit is still communicating with the vehicle may lead to ECM problems 
on some vehicles. Exit diagnostics applications before powering off. 

 

To power down the display tablet

 

1.  Long press the Lock/Power Button. 

2.  Tap 

Power off

 option.   

3.  Tap 

OK

, the tablet will turn off in a few seconds. 

Reboot System 

In  case  of  system  crash,  long  press  the  Lock/Power  button  and  tap 

Reboot

 option to reboot the system.   

Summary of Contents for MaxiPRO MP808TS








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands