AUSTRALIAN MONITOR AMIS120 Series Operating Manual Download Page 1

Clever Features, Contactor Friendly

Operating Manual

AMIS60, 60w Mixer Amplifier

&

AMIS120, 120w Mixer Amplifier

Product Description

The AMIS60 and AMIS120 mixer amplifiers are designed for commercial installations. Both models
operate on 110 VAC, 60Hz or 24 VDC, and may be desk or rack mounted (rack mount kit supplied fitted).
Both amplifiers incorporate a 6 zone 70 volt line speaker zone selector with “All Call”. The AMIS60 will
deliver 60 watts into a load of 8 ohms, 25 volt or 70 volt line. The AMIS120 will deliver 120 watts into a
load of 4 or 8 ohms, 25 volt or 70 volt line. Both Models feature 4 universal mic/line inputs, a transformer
balanced, 600 ohm telephone input and an insert point for additional EQ or feedback exterminator if
required. The AMIS60/120 also feature a dual RCA tape output while a balanced, 700mV XLR output is
also provided to feed up to six power amplifiers. Other standard features include on-board Bell, Pre
Announce, Alert & Evac tones, Remote Master VCA Control  & dual stage priority muting.  As standard,
both models are self standing and come with rubber feet. They may be stacked to a maximum of four units
high.

Thank You For Your Business, We Appreciate Your Support

Summary of Contents for AMIS120 Series










Reviews: