1
1
C
C
H
H
A
A
N
N
N
N
E
E
L
L
T
T
E
E
M
M
P
P
E
E
R
R
A
A
T
T
U
U
R
R
E
E
T
T
R
R
A
A
N
N
S
S
M
M
I
I
T
T
T
T
E
E
R
R
1
1
2
2
O
O
F
F
2
2
5
5
1
1
2
2
0
0
-
-
3
3
5
5
9
9
-
-
1
1
2
2
T
T
Y
Y
P
P
E
E
S
S
I
I
L
L
B
B
U
U
S
S
-
-
T
T
X
X
1
1
T
T
U
U
S
S
E
E
R
R
M
M
A
A
N
N
U
U
A
A
L
L
I
I
s
s
s
s
u
u
e
e
:
:
0
0
5
5
Note: The red "RUN/PROG" switch (see Photograph 2) next to the console port connector
should be in the run position (pushed towards console port connector) at all times.
When in "RUN" mode, for the console port to operate, the SILBUS network needs to be
connected to the SILBUS port. The TX1T will take 10-20 seconds to respond to the
connecting of the console port cable, as it has to change modes. When in console port
configuration mode, no SILBUS operation can take place. Alternatively without SILBUS
network power, you can configure the TX1T in "PROG" mode (switch away from console
port connector - as labelled) using the MEAN1 3.3V power source with the CPP switched
on. This can be done away from a SILBUS network or when commissioning the system
without SILBUS power on. You
must
place it back into "RUN" mode or the TX1T will not
work after the configuration.
6.2 HELP COMMAND
The HELP command prints a list of all available commands and shows the syntax for each
command. Optional command modifiers are shown within [ ] while mandatory modifiers
are shown within < >. An example of a screen output follows:
TX1T::>help
Software 1V04 0x0D5C Configuration 0x4BE4 SN:15065498
Commands:
-------------------------------------------------------------------------------
********** Level 1: Standard Menu **********
HELP [1..7] Level of Help Display Help Menu
REPEAT [LF] [Refresh rate in seconds] Repeat Previous Command
VER Firmware Version and Checksum
STACK Display Peak Stack Usage
SBADDR [<SET> <A1-P8,DISABLE>] Temperature SILBUS Address
FSTMRK [<SET> <A1-P8,DISABLE>] Set Fastlink Marker Address
ANASEL [<SET> <Analnk|Fstlnk>] Analog Protocol for Temperature
ADDPT [<SET> <A1-P8> <FALL|RISE> <Temp>] Add Temperature Trip Points
DELPT [<SET> <Number | all>] Deletes Temperature Trip Points
FLTHYS [<SET> <degC>] Trip Clear Hysteresis Value
RANGE [<SET> <Normal|Wide>] Normal -10to100, Wide -20to200
TEMP Display Temperature in degC
CFGUP Upload Configuration Text
CFGDWN Download Configuration Text
-------------------------------------------------------------------------------
TX1T::>
6.3 REPEAT COMMAND
The REPEAT command is used after another command to continuously repeat that
command. As an example, the TEMP command can be executed followed by the
REPEAT command to provide a continuously updating display of the selected SILBUS
channel. The display will continue to update until any key is hit. The TX1T will respond by
displaying the prompt.
TX1T::>TEMP
Temperature = 0.1degC
