5.4.4.
Earth connection, external
6.
Operation................................................................................................................................
6.1.
Manual operation
6.1.1.
Manual operation: engage
6.1.2.
Manual operation: disengage
6.2.
Motor operation
6.2.1.
Local operation
6.2.2.
Actuator operation from remote
7.
Indications..............................................................................................................................
7.1.
Indication lights
7.2.
Mechanical position indicator/running indication
8.
Signals.....................................................................................................................................
8.1.
Feedback signals via output contacts (binary)
8.2.
Feedback signals (analogue)
9.
Commissioning (basic settings)...........................................................................................
9.1.
Heat-up time for low temperature version
9.2.
End stops in part-turn actuator
9.2.1.
End stop CLOSED: set
9.2.2.
End stop OPEN: set
9.3.
Switch compartment: open
9.4.
Torque switching: set
9.5.
Limit switching: set
9.5.1.
End position CLOSED (black section): set
9.5.2.
End position OPEN (white section): set
9.6.
Intermediate positions: set
9.6.1.
Running direction CLOSE (black section): set
9.6.2.
Running direction OPEN (white section): set
9.7.
Test run
9.7.1.
Direction of rotation: check
9.7.2.
Limit switching: check
9.7.3.
PTC tripping device (option): test
9.8.
Potentiometer setting
9.9.
Electronic position transmitter RWG: set
9.10.
Mechanical position indicator: set
9.11.
Switch compartment: close
10.
Commissioning – controls settings.....................................................................................
10.1.
Controls: open
10.2.
Type of seating: set
10.3.
Push-to-run operation or self-retaining: set
10.4.
Running indication (blinker transmitter): activate/deactivate
10.5.
Torque fault in collective fault signal: activate/deactivate
10.6.
Positioner
10.6.1.
Input ranges (signal type) for setpoint and actual value
10.6.2.
Behaviour on loss of signal (actuator reaction)
10.6.3.
Adjustment in end positions
10.6.4.
Sensitivity setting
10.7.
EMERGENCY command (EMERGENCY - OPEN/EMERGENCY - CLOSE)
10.8.
Controls: close
3
SQEx 05.2 – SQEx 14.2 / SQREx 05.2 – SQREx 14.2
AMExC 01.1
Table of contents
Summary of Contents for AMExC 01.1
