manualshive.com logo in svg

AUMA ACV 01.2, Manual

Share
Download
AUMA ACV 01.2 Manual Download Page 97

Required user level:

Specialist (4)

 or higher.

Customer settings M0041

Interlock M0664

Running dir. Interlock M0666

Default value:

OPEN and CLOSE

Setting values:

OPEN

The enable signal is only required for operation commands in direction OPEN.

CLOSE

The enable signal is only required for operation commands in direction CLOSE.

OPEN and CLOSE

The enable signal is required for operation commands in directions OPEN and
CLOSE.

9.7.

Local Stop

Properties

●

The function Local Stop can be used to stop an operation from Remote locally
with the push button STOP.

●

All operation commands are interrupted.

Information

After releasing push button STOP, an operation command which might still be present
will become active immediately.

9.7.1.

Behaviour

Required user level:

Specialist (4)

 or higher.

Customer settings M0041

Local controls M0075

Local STOP M0627

Default value:

Off

Setting values:

Off

Push button STOP can only interrupt an operation in operation mode 

Local

 (selector

switch = position Local control).

Sel.sw.Local + Remote

In the operation modes 

Local

, 

Remote

, 

Remote II

, 

EMERGENCY

 and 

Service

, push

button STOP interrupts an operation.

Information

In operation mode 

Disabled

, an interruption is NOT possible.

9.8.

EMERGENCY stop function

Conditions

An EMERGENCY stop button (latching) is either located on the electrical connection
or outside.

Characteristics

●

In an emergency, the EMERGENCY stop button can be used to interrupt the
power supply. Possibly available operation commands will be reset via self-re-
taining.

●

The indication in the top row of the display shows:

EMCY stop

97

Actuator controls 
ACV 01.2/ACVExC 01.2 Profibus DP 

Failure functions

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands