manualshive.com logo in svg

AUMA ACV 01.2, Manual

Share
Download
AUMA ACV 01.2 Manual Download Page 86

Execute last CMD

The actuator executes the last operation command before it is stopped.

If the last operation command was a setpoint definition via analogue input (AIN 1/AIN
2), the lower limit of the setpoint position is used (parameter 

Low limit AIN 1

/

Low

limit AIN 2

). The actuator is operated to the defined end position, usually end position

CLOSED.

Behaviour depending on the selector switch position

Once the failure operation is triggered, the defined position is approached. If the
actuator is then moved to another position (e.g. by manual operation), it will try to
perform the set failure operation while the selector switch is in position Remote
control (REMOTE).

Information

To prevent a new approach to the failure position during manual operation, the se-
lector switch must be set to position Local control (LOCAL) or 0 (OFF) prior  to
operating the handwheel.

9.2.4.

Preset position: define

If the 

Approach position

 failure operation is set, the actuator runs to the preset failure

position indicated here.

Required access level:

Specialist (4)

 or higher.

Customer settings M0041

Failure behaviour M0378

Fail.pos.OPEN CLOSE M0387

Default value:

50.0 %

Setting range:

0.0 ... 100.0 %

 (from end position OPEN to CLOSED)

9.2.5.

Failure position MPV: define

This parameter is only available in multiport valve version.

If the 

Approach position

 failure operation is set, the actuator runs to the preset failure

position indicated here.

Required user level:

Specialist (4)

 or higher.

Customer settings M0041

Failure behaviour M0378

Failure position MPV M1172

Default value:

0.0 °

Setting range:

0.0 ... 360 °

9.2.6.

Speed for safety operation: set

The speed during safety operation may be set individually for both direction
(OPEN/CLOSE).

Required user level:

Specialist (4)

 or higher.

Customer settings M0041

Failure behaviour M0378

Failure speed OPEN M1935
Failure speed CLOSE M2042

Default value:

45 rpm

Setting ranges:

6 ... 240 rpm

The adjustable speed range is indicated on the actuator name plate.

86

 Actuator controls

Failure functions

 ACV 01.2/ACVExC 01.2 Profibus DP

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands