AUMA ACV 01.2 Manual Download Page 115

Page: 115 / 168

11.

Functions: activate and enable

11.1.

Functions: activate

Via

Activation

M0212

, functions can be switched on (activated) or off

(deactivated).

Required user level for enabling/disabling:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212

Information

Some functions require enabling. Only enabled functions are visible and can be ac-
tivated or deactivated.

Table 14:

Enabling required

Function

M0589

EMCY behaviour

M0156

Timer CLOSE

M0206

Timer OPEN

Yes

M0158

Positioner

M0294

Operation profile

Yes

M0741

Process controller

M0857

Profibus DP-V2

M0573

Bluetooth

Yes

M0631

Enable LOCAL

Yes

M0770

Priority REMOTE

Yes

M0790

Auto change-over I/O

Yes

M0663

Interlock

M0796

Torque wrn

Yes

M0851

PVST

Yes

M0941

By-pass function

M1136

Maintenance signals

M1137

Maintenance interval

M1884

Maintenance reminder

Yes

M1197

Limit sw. via CDT/App

M1236

Fieldbus operation

M1650

Split range operation

Yes

M1679

Automatic deblocking

M1842

DMF evaluation

M1890

Mean value curves

M1709

Com. eval. REMOTE

Yes

M2122

Speed profile

11.2.

Functions: enable

Via

Enabling

M0179

, optional functions can be enabled or disabled.

This menu is visible in the display from user level

Specialist (4)

Device configuration M0053

Application functions M0178

Enabling M0179

115

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Functions: activate and enable

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Brands by name

Popular brands