AUMA ACV 01.2 Page 112 Manual Download | Manualshive

Page: 112 / 168

background image

On

Monitoring is activated. Should the auxiliary voltage 24 V DC for supplying the control
inputs fail, a warning will be issued.

Activate monitoring of external supply 24 V DC

Required user level:

Specialist (4)

.

Device configuration M0053

Monitoring function M0645

Monitor 24 V DC ext. M0649

Default value:

Function not active

Setting values:

Function not active

Monitoring is deactivated.

On

Monitoring is activated. Should the external supply 24 V DC fail, a warning will be
issued.

10.8.

Temperature monitoring

Characteristics

If the respective sensors are installed in the devices, the actuator controls monitor
different temperatures.

If certain temperature limits are exceeded or fallen short of, the controls either send
a warning or a fault signal.

Conditions:

●

For temperature within the control unit of the actuator: MWG (magnetic limit
and torque transmitter)

●

For motor temperature: additionally temperature sensor (PT 100) in the motor

●

For gear housing temperature: additionally temperature sensor (PT 100) in the
gearing

Information

Current device temperatures can also be displayed. Refer to <Display device tem-
peratures>.

10.9.

Heater system/heater monitoring

The heater system within the actuator controls housing and the heater on the control
unit (within the switch compartment of the actuator) can be monitored. If the monitoring
is activated the following warning will be generated if the heater system or the heater
(circuit = interrupted) fails:

●

In the display of the local controls, status indication

S0005 Warnings

-

Details:

Internal warning Wrn heater

●

Via fieldbus:

Wrn heater

For further information on the heater system and the heater refer to separate <Heater
system and heater> chapter.

Activate heater system monitoring

Heater system monitoring monitors all connected heaters for failure.

Required user level:

Specialist (4)

.

Device configuration M0053

Monitoring function M00645

Monitor heat. system M0647

Default value:

Function not active

Setting values:

Function not active

Heater monitoring is deactivated.

Function active

Heater monitoring is activated.

112

Actuator controls

Monitoring functions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
110
111
112
113
114
...
»

Summary of Contents for ACV 01.2









































































































































































Reviews:

No comments

Related manuals for ACV 01.2

Brand: Ubisys Pages: 2

Brand: GBD Pages: 68

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 20

Brand: Eaton Pages: 4

Brand: Eaton Pages: 10

Brand: Eaton Pages: 288

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Parkside Pages: 65

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 2

Brand: ValvTechnologies Pages: 20

Brand: LLURIA Pages: 2

Brand: Abocom Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands