AUMA ACV 01.2 Page 101 Manual Download

Page: 101 / 168

9.9.7.

PVST operating time: set

During operating time controlled PVST execution (parameter

PVST operation mode

M0889

End position test

), this parameter determines the permissible PVST

operating time.

Customer settings M0041

PVST M0852

PVST operating time M0890

Default value:

00:02.0 min:s

(2 seconds)

Setting range:

00:00.1 ... 15:00.0 min:s

(minutes:seconds)

9.9.8.

PVST reversing time: set

Waiting time during PVST prior to returning to initial position.

Customer settings M0041

PVST M0852

PVST reversing time M0891

Default value:

00:02.0 min:s

(2 seconds)

Setting range:

00:00.1 ... 15:00.0 min:s

(minutes:seconds)

9.9.9.

PVST reminder

If this function is active, a signal is generated if no PVST was executed during the
reminder period.

Activate reminder

Required user level:

Specialist (4)

or higher.

Customer settings M0041

PVST M0852

PVST reminder M0892

Default value:

Function not active

Setting values:

Function not active

Reminder not activated.

Function active

Reminder activated.

Set reminder period

Customer settings M0041

PVST M0852

PVST reminder period M0893

Default value:

0 d

Setting range:

0 ... 65535 d

(days)

9.9.10.

Speed for PVST: set

The speed during PVST may be set individually for both directions (OPEN/CLOSE).

Required user level:

Specialist (4)

or higher.

Customer settings M0041

PVST M0852

Speed PVST Open M2056
Speed PVST Close M2057

Default value:

45 rpm

Setting ranges:

6 ... 240 rpm

101

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Failure functions

Summary of Contents for ACV 01.2









































































































































































Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands

AUMA ACV 01.2, Manual

Search results

Summary of Contents for ACV 01.2

Reviews:

Related manuals for ACV 01.2

Brands by name

Popular brands