manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

760

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Service and Maintenance

Backing Up and Recovering Configuration Data
Inserting a Restoration Point for Configuration Data

- Names of internal subscribers

- Passwords of PBX, subscribers, VoIP accounts and VoIP subscribers

- Address books of the PBX

- Connection data sets with destination, source, and time information of a 
telecommunication connection

Before the data backup is being saved, all subscribers to the PBX must be 
informed that these contents will be forwarded. They must also be informed 
about who will use the data received.

It is absolutely necessary to store the data safely and in accordance with the 
legal requirements.

If you want to make the data backup available to your specialised dealer or 
to the manufacturer for error analysis, you must make sure that the legal 
requirements are fulfilled.

Proceed as follows:

•

Using the configuration manager

1. Open the page 

Administration > Data backup

.

2. Select or clear the check boxes of the data to be stored under 

READ CONFIGU-

RATION DATA FROM THE PBX

.

3. Click 

Read from PBX

 under 

READ CONFIGURATION DATA FROM THE PBX

.

4. Accept the legal notes by entering 

ok

 in the entry field.

5. Click 

Data backup

.

6. Save the configuration file on the PC.

Inserting a Restoration Point for Configuration Data

Proceed as follows:

•

Using the configuration manager

1. Open the page 

Administration > Data backup

.

2. Click 

Insert restoration point

.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Aastra MX-ONE Installation Instructions Manual preview
MX-ONE
Brand: Aastra Pages: 157
Panasonic KX-NS1000 Manual preview
KX-NS1000
Brand: Panasonic Pages: 542
New Rock Technologies OM200 Administrator'S Manual preview
OM200
Brand: New Rock Technologies Pages: 55
New Rock Technologies OM10 User Manual preview
OM10
Brand: New Rock Technologies Pages: 75
Gigaset Pro series Hybird 120 Manual preview
Pro series Hybird 120
Brand: Gigaset Pages: 423

Brands by name

Popular brands

Load more brands