Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 750 / 932

background image

750

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Service and Maintenance

Firmware Update
Initiating a Manual Firmware Update

Regular Firmware Updates for the Connected COMfortel System Telephones via the
Update Server

If the regular firmware update option is enabled, you can specify the frequency and time period
in which the system is to look for new firmware. The firmware update is then triggered automat-
ically once a connection to the update server has been set up and new firmware has been
found.

Initiating a Manual Firmware Update

Proceed as follows:

•

Using the configuration manager

Requirements:

•

A firmware file (*.rom) saved on a data storage device (PC)

Note:

You can find a new firmware file on the Internet (see

www.auerswald.de/service

). Alternatively, you can get a new firmware file

from your specialised dealer.

1. Open the page

Administration > Firmware update/restart

.

2. Click

Start firmware update

under

STORE THE FIRMWARE IN THE PBX(MANUAL

FIRMWARE UPDATE)

.

3. Click

Browse

(this text is dependent on the operating system used).

4. Select the firmware file (*.rom) you want and click

Open

(this text is dependent on the

operating system used).

The path and the file name are displayed in the

Firmware Update

field.

5. Click

Import

.

The firmware update is started. As soon as the firmware file has been saved in the
PBX, you will receive a message.

6. Click

Initiate reboot

, to restart the PBX and enable the firmware.

The PBX is restarted.

«
...
748
749
750
751
752
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

KX-TVS50 - 2 Port Voicemail System

Brand: Panasonic Pages: 416

Brand: LV switch Pages: 199

Brand: Far south networks Pages: 19

Brand: Panasonic Pages: 274

Brand: Nortel Pages: 46

Succession 1000M

Brand: Nortel Pages: 48

Brand: Nortel Pages: 67

Contact Center Manager

Brand: Nortel Pages: 1618

Berkshire 10K ipPBX

Brand: ATL Pages: 42

COMpact 3000 VoIP

Brand: Auerswald Pages: 2

COMpact 3000 ISDN

Brand: Auerswald Pages: 2

COMmander 6000R Xtension

Brand: Auerswald Pages: 2

COMpact 2206 USB

Brand: Auerswald Pages: 68

COMmander Basic.2

Brand: Auerswald Pages: 84

COMmander Basic

Brand: Auerswald Pages: 84

Brand: Auerswald Pages: 1114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands