Auerswald COMpact 5000 Operation Manual Download

Page: 75 / 932

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Installation and Commissioning

Preparation (COMpact 5000R)

Updating or Upgrading the PBX

A Board guides

B Board lock

Removing a Module

1. Unlatch the board lock, for example with your right thumb.

2. Remove the module with your other hand.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands

Auerswald COMpact 5000, Operation Manual

Search results

Summary of Contents for COMpact 5000

Reviews:

Related manuals for COMpact 5000

Brands by name

Popular brands