manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

707

Settings

PBX Time

Configuring PBX Time (Time and Date) Manually

PBX Time

The PBX has an internal clock that returns the PBX time (time and date) on the connected end 
devices. If the end device is so equipped, the PBX time will be displayed on the end device.

Furthermore, the PBX time is required to carry out functions such as switching configurations 
as well as wake-ups.

During a power failure or PBX reset, the PBX time is lost. There are several ways to update it:

•

Manually

•

Via the network

•

Using the buffered real-time clock – saves the time for approx. two hours in the case of a 
power outage.

•

Via ISDN/external S

0

 port (optional, see chapter Important Information > Product Details > 

Basic Assembly and Extensions)

Note:

 The switch to/from daylight savings is done automatically for the PBX 

time.

Configuring PBX Time (Time and Date) Manually

Proceed as follows:

•

Using the configuration manager

•

Using a character string on the internal telephone (see section Short Reference)

Using the Configuration Manager to Manually Configure the PBX Time

1. Open the page 

Settings > Date/Time of the PBX

.

2. Select the option 

Manual

 under 

ONE-TIME CONFIGURATION OF DATE / TIME

.

3. In the 

Time

 entry field, enter the correct time. Possible entries:

4. In the 

Date

 entry field, enter the current date. Possible entries:

Time in hh format: mm : ss

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Nokia 22 Operator'S Manual preview
22
Brand: Nokia Pages: 54

Brands by name

Popular brands

Load more brands