manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

692

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

Call Distribution
Creating a Call Distribution

8. Repeat step 2 to 7 to configure the call distribution for other configurations (PBX 

profiles).

Switching Linear Call Distribution on the PTP Connection On/Off

If the linear call distribution for the PTP connection is enabled, a 1:1 assignment for the exten-
sions is made automatically for internal numbers and external extensions that are matching the 
extensions block.

Requirements:

•

External S

0

 port, VoIP account (optional, see chapter Important Information > Product 

Details > Basic Assembly and Extensions)

•

Configured connection type PTP connection

•

Entered PBX base numbers with corresponding extensions blocks

1. Open the page 

Public switched tel. networks > Call distribution

.

If several configurations (PBX profiles) have been created, these will be available as 
tabs.

2. With several configurations: Click the tab with the desired configuration.

3. In the first 

CALL DISTRIBUTION FOR...

 list field, select 

ISDN PTP connections

 or 

VoIP PTP connections

.

4. In the second 

CALL DISTRIBUTION FOR...

 list field, select the connection.

5. Select or clear the 

Linear call distribution (external = internal)

 check box.

6. Click 

 

Save

.

7. Repeat step 4 to 6 to switch on/off linear call distribution for the other PTMP connec-

tions.

8. Repeat step 2 to 7 to switch on/off linear call distribution for other configurations (PBX 

profiles).

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Samsung OfficeServ 7100 Series Provisioning Manual preview
OfficeServ 7100 Series
Brand: Samsung Pages: 5
H3C XE 200 IP Operation Manual preview
XE 200 IP
Brand: H3C Pages: 514
NEC XN120 2OPBOX Manual preview
XN120 2OPBOX
Brand: NEC Pages: 8
Bogen MULTICOM 2000 Installation Instructions Manual preview
MULTICOM 2000
Brand: Bogen Pages: 32
New Rock Technologies OM20 Quick Installation Manual preview
OM20
Brand: New Rock Technologies Pages: 2

Brands by name

Popular brands

Load more brands