manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

663

Settings

DECT Telephones

Using the Configuration Manager to Switch On the Login Mode of a COMfortel DECT 900 Base

COMfortel WS-400 IP or COMfortel WS-650 IP with COMfortel M-100/200

The IP DECT server is connected to and operated on the PBX via the Ethernet port and internal 
VoIP channels (optional, see chapter Important Information > Product Details > Basic 
Assembly and Extensions).

In connection with a COMfortel WS-400 IP or COMfortel WS-650 IP, the COMfortel M-100/200 
handsets are operated on the PBX as IP DECT telephones. The chapter Settings > Internal 
Telephone Numbers > Creating VoIP or IP DECT Subscribers describes how you can create 
internal numbers for these mobile handsets.

The Setup Guide of the IP DECT server describes how you can log a COMfortel M-100/200 on 
to the IP DECT server.

The chapter Address Books and Lists > LDAP Server describes how you can take over 
telephone book entries for the COMfortel M-100/200 handsets.

Using the Configuration Manager to Switch On the Login Mode of a COMfortel 
DECT 900 Base

If the login mode of a COMfortel DECT 900 Base is enabled, up to five mobile handsets can be 
logged in to the base station.

Note:

 A maximum of three mobile handsets are recommended for a 

COMfortel DECT 900 Base because only three mobile phones can be called 
at the same time.

Proceed as follows:

•

Using the configuration manager

Requirements:

•

COMfortel DECT 900 Base connected to the internal S

0

 port (optional, see chapter 

Important Information > Product Details > Basic Assembly and Extensions)

•

COMfortel DECT 900/900C Handsets

•

Configured internal numbers for the COMfortel DECT 900/900C Handsets

1. Open the page 

Subscriber (scr.) > COMfortel DECT

.

2. Select the DECT base in the list field under 

DECT base

.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Bosslan BOSST101 Manual preview
BOSST101
Brand: Bosslan Pages: 84
Orchid Telecom 416+ Programming & User Manual preview
416+
Brand: Orchid Telecom Pages: 25
Yeastar Technology S20 Installation Manual preview
S20
Brand: Yeastar Technology Pages: 12
Commander Connect Connect V6 Owner'S Manual preview
Connect V6
Brand: Commander Connect Pages: 138

Brands by name

Popular brands

Load more brands