Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 648 / 932

background image

648

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

VoIP
VoIP Account Settings

LCR

Requirements:

•

Network provider must support the dial-around service

•

Configured prefixes (country prefix and local area code)

•

Configured LCR (see Functions > LCR section)

The VoIP account is used for LCR calls.

Notes:

LCR must be disabled if the network provider does not support LCR.

However, you can always perform LCR manually by dialling a provider area
code prefix if the network provider supports the dial-around service.

Routing via exception numbers (VoIP + GSM + LCR)

Requirements:

•

Exception numbers (VoIP/GSM routing) are set up

The device checks whether the destination number involved in call forwarding for external

numbers has been set up as an exception number. If so, the call is sent along the configured
path. If the destination number has not been entered in the routing table, the call to be
forwarded is sent either via a VoIP call channel or via any free call channel (

For call

forwarding via the PBX, use any available call channel

).

PHONE NUMBERS FOR PTP CONNECTION

PBX base number

Extensions block (DDI numbers)

From

To

Requirements:

•

prefixes (country and local area code) configured for the VoIP account

A PTP connection has a PBX base number (base number, header, base phone number) and
(Direct Dial In - DDI) extension numbers. The VoIP provider assigns the phone numbers for the
connection. The phone number to be dialled is formed from the PBX base DDI
number.

«
...
646
647
648
649
650
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 892

Brand: Panasonic Pages: 272

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands