manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

602

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

Analogue Connection
Expert Configuration, Analogue Connection

Tones

Dial tone 1 (normal dial tone)

 

Dial tone 2 (special dial tone)

 

Dial tone 3 (Centrix tone)

 

Busy signal 1 (call target busy)

 

Busy signal 2 (network busy)

 

Call tone 1

 

Call tone 2

 

Special interest tone

 

The character strings show which tones are sent by the analogue network provider. This means 
the PBX can then identify the tones and apply them accordingly.

The network provider uses these tones in the following situations:

• Dial tone

: When a subscriber picks up the call.

• Busy signal

: If the required connection is busy (busy signal 1), or if the network is 

overloaded (busy signal 2, e.g. directly after dialling the local area code).

• Call tone

: During the call phase.

• Special interest tone

: If the dialled phone number is not present, and the network provider 

has not recorded a special announcement for this situation.

Notes:

Please contact the Support team before making any changes to these 
character strings.

An incorrect character string will cause the PBX to operate incorrectly.

Ring Signal

Frequency

 

The ringer frequency specifies which frequency is used by the analogue network provider to 
send the ring signal.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Yeastar Technology MyPBX-SOHO Administrator'S Manual preview
MyPBX-SOHO
Brand: Yeastar Technology Pages: 204

Brands by name

Popular brands

Load more brands